86-755-89208647
1501, First Unit, Xingjiangyuan Bldg. 10, Xiangjiangshijicheng, Kaifu District, Changsha, Hunan, China (Mainland)
1.Inspecting Package Contents
When you get a new JDS6600 series dual channel DDS signal generator, please inspect device as follows:
1.1 Inspect the shipping container for damage.
If there are damages in the container or foam, keep them until the whole machine and the accessories passing the electrical and mechanical tests. If your instrument has damaged during shipping, please contact your seller and us for compensation.
1.2 Check the Accessories
All contents are as follows, if there is missing, damage or wrong, please contact us or reseller.
Host:JDS6600 | 1pcs |
Accessories:DC adapter | 1pcs |
USB cable | 1pcs |
Signal output cable | 2pcs |
User manual (PDF) | 1pcs |
CD | 1pcs |
1.3 Check the instrument
In case of any mechanical damage or defect, or if the instrument does not operate properly or pass the electrical and mechanical tests, you can contact us or reseller.
2. Summary
2.1 Brief Introduction
JDS6600 series DDS signal generator can generate sine wave, square wave, triangle wave, pulse wave, and arbitrary wave etc. The frequence will be upto 40MHz. And it has duty-cycle correction, amplitude modulation function and frequency sweep function, etc. It can show output signal, amplitude and frequency in the same time. This series has amplitude frequency characteristics, and the appearance is very delicate and beautiful. It can be applied in factories, schools, research institutes and laboratories.
2.2,Model Introduction
There are 3 models, JDS6600-40M, JDS6600-25M and JDS6600-08M. The main difference is the max output frequency of sin wave, as follows:
Model | The max output frequency of sin wave |
JDS6600-40M | 40MHz |
JDS6600-25M | 25MHz |
JDS6600-08M | 8MHz |
2.3
Note :Unit mm
Frequency Characteristics | ||||||||||
| JDS6600-08M | JDS6600-25M | JDS6600-40M | |||||||
Sine frequency range | 0~8MHz | 0~25MHz | 0~40MHz | |||||||
Square frequency range | 0~8MHz | 0~15MHz | 0~15MHz | |||||||
Triangle frequency range | ||||||||||
Pulse frequency range | 0~6MHz | 0~6MHz | 0~6MHz | |||||||
CMOS/TTL digital frequency range | ||||||||||
Arbitrary wave frequency range | ||||||||||
Square rise time | ≤30nS | ≤25nS | ≤20nS | |||||||
Mininum Frequency resolution | 0.01µHz(0.00000001Hz) | |||||||||
Frequency accuracy | ±20ppm | |||||||||
Frequency stability | ±1ppm/3h | |||||||||
Waveform Characteristics | ||||||||||
Waveform | Sine, Square, Triangle, Pulse (duty-cycle correction),Partia Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sinc Pulse, Lorentz Pulse, and 60 kinds user defined waveform. | |||||||||
Waveform length | 2048 points | |||||||||
Waveform sampling rate | 200MSa/s | |||||||||
Waveform vertical resolution | 12 bits | |||||||||
Sine | Harmonic suppression | ≥45dBc(<1MHz); ≥40dBc(1MHz~20MHz) | ||||||||
Total harmonic distortion | <0.8%(20Hz~20kHz,0dBm) | |||||||||
Square and Pulse | Overshoot (Square) | ≤5% | ||||||||
Duty-cycle range(Pulse) | 0.1%~99.9% | |||||||||
Ramp wave | Linearity | ≥98%(0.01Hz~10kHz) | ||||||||
Output Characteristics | ||||||||||
Amplitude range | JDS6600-08M | JDS6600-25M | JDS6600-40M | |||||||
2mVpp~20Vpp | ≤10MHz:2mVpp~20Vpp ≤16MHz:2mVpp~10Vpp ≤25MHz:2mVpp~5Vpp | ≤10MHz:2mVpp~20Vpp ≤16MHz:2mVpp~10Vpp ≤25MHz:2mVpp~5Vpp | ||||||||
Amplitude resolution | 1mV | |||||||||
Amplitude stability | ±0.5%/5 h | |||||||||
Amplitude flatness | ±5%(<10MHz); ±10%(>10MHz) | |||||||||
Waveform Output | ||||||||||
Output impedance | 50Ω±10%(typical) | |||||||||
Protection | All the signal output termianl can be shorted within 60s | |||||||||
DC Offset | ||||||||||
Offset adjusting range | Output Amplitude >4V | 0.4V | 0 | |||||||
-9.99V~9.99V | -2.5V~2.5V | -0.25V~0.25V | ||||||||
Offset resolution | 0.01 V | |||||||||
Phase characteristics | ||||||||||
Phase adjusting range | 0~359.9° | |||||||||
Phase resolution | 0.1° | |||||||||
TTL/COMS Output | ||||||||||
Low level | <0.3V | |||||||||
High level | 1V~10V | |||||||||
Level rise/fall time | ≤20ns | |||||||||
External Measurement Function | ||||||||||
Frequency meter function | Frequency measurement range | 1Hz~100MHz | ||||||||
Measurement accuracy | Gate time continuously adjusted between0.01s~10s | |||||||||
Counter function | Counting region | 0-4294967295 | ||||||||
Coupled mode | 2kinds Coupling modes, DC and AC | |||||||||
Control mode | Manual operation | |||||||||
Input signal voltage range | 2Vpp~20Vpp | |||||||||
Pulse width measurement | 0.01us (resolution), 20s (MAX measuring time) | |||||||||
Period measurement | 0.01us (resolution), 20s (MAX measuring time) | |||||||||
Sweep Function | ||||||||||
Sweep channel | CH1 or CH2 | |||||||||
Sweep type | linear sweep,log sweep | |||||||||
Sweep time | 0.1s~999.9s | |||||||||
Setting range | User settings | |||||||||
Sweep direction | Forward, Backward and Roundtrip | |||||||||
Burst function | ||||||||||
Number of pulses | 1-1048575 | |||||||||
Burst mode | Manual Trig,CH2 Trig,Ext.Tring(AC) ,Ext.Tring(DC) | |||||||||
General technical parameters | ||||||||||
Display | Display type | 2.4 inch TFT color LCD | ||||||||
Storage and loading | Quantity | 100 groups | ||||||||
Location | 00 to 99(Power on will load the position 00) | |||||||||
Arbitrary wave | quantity | 1 to 60, totally 60 groups(default set 15 groups) | ||||||||
Interface | Interface mode | USB to serial interface | ||||||||
Extension interface - | There is serial interface of TTL level mode to be convenient for user development. | |||||||||
Communication speed | 115200bps | |||||||||
communication protocol | Command-line mode, Open protocol | |||||||||
Power supply | Voltage range | DC5V±0.5V | ||||||||
Manufacturing process | Surface-mount technology, FPGA design, high reliability, long service life | |||||||||
Buzzer | User can set ON or OFF by procedure | |||||||||
Operating characteristics | Full button operation, knob continuous adjustment | |||||||||
Environmental conditions | Temperature:0~40 oCHumidity:<80% | |||||||||
